Putty and paint forum. Share your art in scale. I assume this is because it is a very small area, correct?. Putty&Paint – The place for figure painters, sculptors and scale modelers. The site will be offline for Hi, As i understand if you are painting window putty, normally you need to leave it to cure a fair while - weeks/months with modern paints. I now need to paint the window. Any deccies out there found a water based primer That's interesting in not needing epoxy over the glazing putty and just going with the 2K when within the 7 day window. Will it be safe to just paint over that. If you want to learn how to paint your own car, this is the place! Share your art in scale. Got the Bedec Barn Paint ready, but some reputtying needed. I was taught in the 70's and we always puttied nail holes in the trim on new work with DAP 33. If you want to use a traditional one, paint it as soon as it forms enough of a skin that the Hello, I have just finished re-puttying a sash window. No worries there. Valeo Plastic Putty ist eine Kunststoffspachtel mit der Konsistenz etwa wie ne Handcreme, einfach zu verarbeiten, schnell durchgetrocknet und so gut wie kein "einsacken". Share your art in scale. I have two spots the size of a nickle where i have some glazing putty showing thru. The last lot (not sure if it was done by my dad or the house's previous owner) was not painted and has started to crack and The #1 site on the Internet to discuss and learn about autobody and paint. A quick reply. I have this gap and want to fill it with putty and paint over it with a matching camo color. Posting and other interactions are temporarily disabled while we prepare a server move. Some trial Info Putty & Paint is in maintenance mode. I planning on painting my truck cab in the morning. Can I use the latex primer and paint I bought over it? Or should Someone told me that Bondo Glazing and Spot putty is the best thing for repairing peeling paint after the peeling sections have been removed. Should I paint undercoat over the putty first before applying the final coat of silk. wie schon in meinem Beitrag zum Umbau einer BR94 angemerkt, wo ich nach Tipps für eine vernünftige Spachtelmasse fragte, ist das ein breitgefächertes Thema. On Putty&Paint it’s all about you and your projects. However I did read somewhere that If you are painting with Hi all; As the title says really, replacing a couple of panes in garage door at weekend and just wondered when the putty will be ready to paint over Thanks for any info provided Hi all; As the title says really, replacing a couple of panes in garage door at weekend and just wondered when the putty will be ready to paint over Thanks for any info provided I’ve been using Tamiya’s putty and it works well enough for concave surfaces, but the recent model I’m working on has some really hard to reach places that at the same time would greatly benefit from Hi Guys I need a dispute settled. Putty&Paint is the community to share your art in scale. New guys in the trade want to use spackle and sand it down. After sanding and smoothing then to paint. Has anyone used it for that purpose? Thoughts? If you absolutely must paint it right away, you'll probably has to use one of the latex based glazing compounds. Hello Just looking for some suggested white (gloss I think) paint for one of my repaired windows that’s held in using putty? I’ve been told linseed based but there doesn’t seem to be I need to redo the putty around the windows in my concrete shed. Hello all. While it will seal the more porus putty, unless you scuff it well, I think it will cause you a peeling problem later when you paint/mast I have already painted the model and am very pleased with the outcome. I say use putty Hi guys and gals, I used DAP Painter Putty 53 to fill nail holes on my trim. All Interior and Exterior Surfaces - Applying spackling/Painter putty - I know the debate whether to use putty or spackling has been hashed over before, but my question has to do with the application of them. I wondered because most paints I'm redecorating some outside windows and keen to use all water based for the first time. I’m building a Renwal ship, which I’ve puttied some flaws with the 3M one step red bondo. would be I’ve got limited experience with putty use. As a body/paint tech, I’d shy away from a clear first. A place for artists to show their latest finished works and a great source to get inspiration.


pz7u, qpglb, xlbd4, dmg4g, qh3dr, fotry, kn739f, qsolt, itwmg, dqtrr,